How do you start to Process your cases?
- sonic306090
- Posts: 64
- Joined: 11 Jan 2021 19:17
- My Press Choice: Turret
- Location: Channahon, IL
- Has thanked: 107 times
- Been thanked: 10 times
How do you start to Process your cases?
Hi All, I usually wet tumble my Shot 9mm cases when I get home from the range, Out of 200 practice shots, I'm able to pick up around 150 casings. I wet tumble primed bullets with Stainless steel media and Gun Tap.
I wipe and let dry for a couple of days and then I Deprime and size with a bit of lube. I wet tumble again. I wipe off and put it at the end of the line of prepared cases and start my loading on the next cases in line from processed a couple of months ago. I have about 900- 9mm cases in line to reload before I get to these, so They would be up there for few months before I get to them. I only reload about 300 cases a month.
I wipe and let dry for a couple of days and then I Deprime and size with a bit of lube. I wet tumble again. I wipe off and put it at the end of the line of prepared cases and start my loading on the next cases in line from processed a couple of months ago. I have about 900- 9mm cases in line to reload before I get to these, so They would be up there for few months before I get to them. I only reload about 300 cases a month.
Thank you for any advice!
Mark 9mm
Mark 9mm
- RBHarter
- Founding Member
- Posts: 2047
- Joined: 13 Mar 2014 19:45
- My Press Choice: Single Stage
- Location: The green hell 90 miles north of Texarka
- Has thanked: 76 times
- Been thanked: 672 times
Re: How do you start to Process your cases?
I clean as needed . I cleaned a couple of 20 mm cans of brass in a vibebratory tumbler a while back . Mostly I just wipe it down . Most of my rifles just get neck sized .
Just a Red neck,White boy, Blue blood American.....
- sonic306090
- Posts: 64
- Joined: 11 Jan 2021 19:17
- My Press Choice: Turret
- Location: Channahon, IL
- Has thanked: 107 times
- Been thanked: 10 times
Re: How do you start to Process your cases?
Do you prefer Dry tumble? It seems like that would leave a lot of Walnut shell dust residue??
I bought that little Harbor Freight rock tumbler for my cases. I think I may have used it about 15 times already.
Still works well. Not bad for 50 bucks.
I bought that little Harbor Freight rock tumbler for my cases. I think I may have used it about 15 times already.
Still works well. Not bad for 50 bucks.
Thank you for any advice!
Mark 9mm
Mark 9mm
- RBHarter
- Founding Member
- Posts: 2047
- Joined: 13 Mar 2014 19:45
- My Press Choice: Single Stage
- Location: The green hell 90 miles north of Texarka
- Has thanked: 76 times
- Been thanked: 672 times
Re: How do you start to Process your cases?
I used corn cob . I tried walnut , it was enough for me .
I had no real trouble with dust . There's no real hurry for me , my processes don't allow for getting in a big hurry . I use single stage presses and load only 50-100 in a typical setting . Although I've been known to size/decap 2-300 a night 3-4 nights at a time , then turn around and repeat flairing 380,9,40,45 . I did 12-1300 223 once .
Batch loading .
I had no real trouble with dust . There's no real hurry for me , my processes don't allow for getting in a big hurry . I use single stage presses and load only 50-100 in a typical setting . Although I've been known to size/decap 2-300 a night 3-4 nights at a time , then turn around and repeat flairing 380,9,40,45 . I did 12-1300 223 once .
Batch loading .
Just a Red neck,White boy, Blue blood American.....
- jwfilips
- Posts: 15
- Joined: 09 Jan 2021 19:44
- My Press Choice: Single Stage
- Location: NEPA
- Been thanked: 5 times
Re: How do you start to Process your cases?
If it is for Rifle brass ( mine never touches the ground): I only Vibrate it in walnut hulls every 8 shooting just before I anneal and FL resize. Otherwise it is only Neck sized and reloaded the previous 7 times:
Now pistol is different! If it is for an autoloader, well they hit the ground and get gritty...so I Decap them with a Lee universal Decap die and Put them in the vibrator to clean them up before putting in my FL sizing dies!
If I find range brass I universal decap Then Citric acid wash then Dry and Vibrate! These will have to be FL sized up front because I do not know what shot them
Now pistol is different! If it is for an autoloader, well they hit the ground and get gritty...so I Decap them with a Lee universal Decap die and Put them in the vibrator to clean them up before putting in my FL sizing dies!
If I find range brass I universal decap Then Citric acid wash then Dry and Vibrate! These will have to be FL sized up front because I do not know what shot them
" Associate with men of good quality, if you esteem your own reputation:
for it is better to be alone than in bad company. " - G. Washington,
56th Rule
for it is better to be alone than in bad company. " - G. Washington,
56th Rule
- sonic306090
- Posts: 64
- Joined: 11 Jan 2021 19:17
- My Press Choice: Turret
- Location: Channahon, IL
- Has thanked: 107 times
- Been thanked: 10 times
Re: How do you start to Process your cases?
Interesting, It seems Rifle reloading is somewhat of a different beast, from what I'm learning, but for now, I'll stick to concentrating on loading 9mm. There seems to be a lot to learn! I'm a small size reloader as well. I put the time & care into each cartridge that I load. I'm in no hurry to load them all. Just as long as I can get at least 100 pcs every two weeks, the wife and I are happy:)
Thank you for any advice!
Mark 9mm
Mark 9mm
-
- Founding Member & Supporter
- Posts: 1123
- Joined: 20 Dec 2013 11:09
- My Press Choice: Single Stage
- Location: Arizona
- Location: Arizona
- Has thanked: 688 times
- Been thanked: 327 times
Re: How do you start to Process your cases?
First, everything hits the buzz bucket with walnut shell, just to knock the dirt & crud off.
Next, I deprime & resize. Then new to me brass only, gets wet tumbled.
I then, on new to me brass, process the primer pockets, this only needs done once for
the life of the brass. I then check length & trim as needed.
If it's brass I've had for a bit & already did a full smash.process on, I just toss in the buzz
bucket, deprime, load, shoot repeat until they get really grungie then just wet tumble.
Brass cleaning & prep is without a doubt, the most talked about but least important part
of handloading!!! When I started banging out 38spec with a Lee Loader 55 years ago,
All I did & most anyone did was wipe off the the spent cases with a rag with a little
mineral spirits on it..
Next, I deprime & resize. Then new to me brass only, gets wet tumbled.
I then, on new to me brass, process the primer pockets, this only needs done once for
the life of the brass. I then check length & trim as needed.
If it's brass I've had for a bit & already did a full smash.process on, I just toss in the buzz
bucket, deprime, load, shoot repeat until they get really grungie then just wet tumble.
Brass cleaning & prep is without a doubt, the most talked about but least important part
of handloading!!! When I started banging out 38spec with a Lee Loader 55 years ago,
All I did & most anyone did was wipe off the the spent cases with a rag with a little
mineral spirits on it..
A day late & A dollar short? Story of my life
- GasGuzzler
- Moderator & Supporter
- Posts: 2044
- Joined: 26 Jan 2016 22:39
- My Press Choice: Turret
- Location: Cooke County, TX
- Has thanked: 330 times
- Been thanked: 501 times
Re: How do you start to Process your cases?
If brass has aged on the ground I do this once before and once after primers removed. Boiling water with a drip of Dawn and 1/8th TSP of LemiShine in my $40 Harbor Freight rock tumbler NO PINS for 30 minutes. Bake to dry in my powder coat oven or air dry in coffee cans in the bed of my truck.
I don't do dry media because it's horribly messy if fine media is used and a royal pain to pick out of primer pockets on larger gauge media.
I don't do dry media because it's horribly messy if fine media is used and a royal pain to pick out of primer pockets on larger gauge media.
__________________________________________________________________________________________
I've always been crazy but it's kept me from goin' insane.
I've always been crazy but it's kept me from goin' insane.
-
- Posts: 39
- Joined: 12 May 2016 15:53
- My Press Choice: Single Stage
- Location: S.E. Wisconsin
- Been thanked: 14 times
Re: How do you start to Process your cases?
I de-cap all my cases first, on a dedicated de-caping press/die, then stainless steel pins/with lemishine, and dish soap tumble them. I like to run "clean" brass thru my dies, less chances of getting scratched dies that way.
Dave
Dave
-
- Founding Member & Supporter
- Posts: 674
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: S. Oregun
- Has thanked: 203 times
- Been thanked: 371 times
Re: How do you start to Process your cases?
My first step is inspection. Even at the range, I'll quick check the overall condition and glance a the headstamp/primer. When I get home my first working step is dry tumbling (corn cob blast media 14-20), but I may look through the cases gain. I tried wet tumbling but my handloads (and ego) don't demand ultra shiny, cases, pristine primer pockets or case interiors and they don't shoot any better. If I want BBQ brass I'll just eave it in my rotary longer. When done cleaning, I'll give them a good close inspection then proceed with my process normally up to primed and ready to charge/seat and box/bag them up for later finishing. I like reloading so I don't use a progressive, no "time saver" gadgets or "improved RPH" methods...