APP press roller handle
-
- Supporter
- Posts: 1003
- Joined: 09 Nov 2015 06:35
- My Press Choice: Single Stage
- Location: Washington State
- Has thanked: 38 times
- Been thanked: 274 times
Re: APP press roller handle
I think I "need" something like that on my 6sp truck. Would have to put a diagram on it though so I could remember where reverse is....and the rest.
Does it say Hurst on it...???? I like it on the press, looks good.
Does it say Hurst on it...???? I like it on the press, looks good.
-
- Posts: 14
- Joined: 18 Jul 2020 16:18
- My Press Choice: Progressive
- Location: Georgia
- Been thanked: 3 times
Re: APP press roller handle
I purchased this back in June from the Reloaders Network, and it certainly is better then the stock one:
https://www.thereloadersnetwork.com/202 ... e-lee-app/
https://www.thereloadersnetwork.com/202 ... e-lee-app/
- mmb617
- Posts: 18
- Joined: 09 Aug 2020 18:23
- My Press Choice: Single Stage
- Location: PA
- Has thanked: 2 times
- Been thanked: 6 times
Re: APP press roller handle
It does indeed.horseman wrote:
Does it say Hurst on it...????
I bracket raced for years in a stick class and always preferred a T-handle so when looking to replace the stock ball this immediately came to mind. I find it quite comfortable.
My roller handle for the APP arrived from Titan yesterday so I'll installing it and trying it out shortly.
- mmb617
- Posts: 18
- Joined: 09 Aug 2020 18:23
- My Press Choice: Single Stage
- Location: PA
- Has thanked: 2 times
- Been thanked: 6 times
Re: APP press roller handle
Well I got it installed and have to say it's quite an improvement. When sizing cases I used to wear a glove because the plastic handle hurt my hand. The fact that it didn't rotate made it rub your hand through the cycle.
The roller handle allows a good grip and rotates as you pull it down which is way more comfortable. I don't need the glove anymore.
The roller handle allows a good grip and rotates as you pull it down which is way more comfortable. I don't need the glove anymore.
-
- Posts: 14
- Joined: 04 Sep 2020 13:00
- My Press Choice: Progressive
- Location: WI
- Has thanked: 1 time
- Been thanked: 3 times
Re: APP press roller handle
I 3d printed my roller handle. I got the file off of thingiverse. Use a 4.5" long 5/16" bolt a couple of skate bearings and thing works great.
-
- Supporter
- Posts: 888
- Joined: 06 Mar 2016 16:09
- My Press Choice: Hand Press
- Location: SW Ohio
- Has thanked: 156 times
- Been thanked: 240 times
Re: APP press roller handle
Damin69 wrote:I 3d printed my roller handle. I got the file off of thingiverse. Use a 4.5" long 5/16" bolt a couple of skate bearings and thing works great.
Curt.......makin' smoke and raising my carbon foot print one cartridge at a time
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
- buckeye43210
- 250 Shots
- Posts: 253
- Joined: 20 Dec 2014 09:47
- My Press Choice: Progressive
- Location: TPA
- Has thanked: 23 times
- Been thanked: 131 times
Re: APP press roller handle
I plan on Leementing my press by swapping the handle brackets (left to right and right to left). The spacing between the brackets is now just over four inches (100 mm). I'll work on a handle replacement over the weekend.
-
- Posts: 32
- Joined: 10 Nov 2019 16:25
- My Press Choice: Single Stage
- Location: MI
- Has thanked: 12 times
- Been thanked: 9 times
Re: APP press roller handle
does the lee handle leave enough room to clear an auto drum powder measure? I looks like it might be wide enough and maybe even tall enough. Can anyone who has both let me know?