Not your typical Load-All - Load All Junior
- Et2ss
- Moderator & Supporter
- Posts: 143
- Joined: 18 Nov 2018 19:56
- My Press Choice: Progressive
- Location: Far too close to the edge
- Has thanked: 4 times
- Been thanked: 68 times
Not your typical Load-All - Load All Junior
I had never seen one of these, but had to scoop it up when I did.
These were mentioned in an article linked IN THIS THREAD on a Unitized Loader. These sold for about half the price of the Load-All
These were mentioned in an article linked IN THIS THREAD on a Unitized Loader. These sold for about half the price of the Load-All
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: Not your typical Load-All - Load All Junior
Yeap, the Jr. No doubt offered to ensure the MEC 12 Gauge Loader did not survive.
You do not have the required permissions to view the files attached to this post.
Michael
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: Not your typical Load-All - Load All Junior
Good find, where did you find it?Et2ss wrote:I had never seen one of these, but had to scoop it up when I saw it.
Michael
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
- Et2ss
- Moderator & Supporter
- Posts: 143
- Joined: 18 Nov 2018 19:56
- My Press Choice: Progressive
- Location: Far too close to the edge
- Has thanked: 4 times
- Been thanked: 68 times
Re: Not your typical Load-All - Load All Junior
Ranch Dog wrote:Good find, where did you find it?Et2ss wrote:I had never seen one of these, but had to scoop it up when I saw it.
FleaBay.
It wasn't labeled as a Load All, Saw it at $12.50 and had to jump.
It didn't come with the sizer ring (not that I plan on actually using it), or dippers, and when it got here the top plastic cap (that was in the auction pictures) was missing from the square aluminium center tube.
I have e-mailed the seller, hopefully they can find it.
- Old Scribe
- Supporter
- Posts: 369
- Joined: 02 May 2015 09:13
- My Press Choice: Turret
- Location: State of Jefferson
- Has thanked: 461 times
- Been thanked: 120 times
Re: Not your typical Load-All - Load All Junior
Cool find!
"Well here's another nice mess you've gotten me into." Oliver Hardy
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: Not your typical Load-All - Load All Junior
I finally got one; new, old stock. There have been a couple on eBay relatively cheap, but they are always missing the sizing ring. This was the complete kit and included a catalog. Honestly, this being the first I've seen in real life, it is a little bitty press and will fit on Bench Plate with a standard hardwood plate.
My plan is to dedicate this press to slug loads so I can use my II for shotshells.
Now, my next Lee "look to find" is a Load-Fast 12 Gauge progressive press. I will pay a finders fee for a working press.
My plan is to dedicate this press to slug loads so I can use my II for shotshells.
Now, my next Lee "look to find" is a Load-Fast 12 Gauge progressive press. I will pay a finders fee for a working press.
Michael
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: Not your typical Load-All - Load All Junior
All set to go, comparing II to Junior.
First Hammerhead slug load.
This is how I will probably use it. Next to the Lee Safety Disk with an Adjustable Charge Bar for dropping the powder charges.
First Hammerhead slug load.
This is how I will probably use it. Next to the Lee Safety Disk with an Adjustable Charge Bar for dropping the powder charges.
Michael
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: Not your typical Load-All - Load All Junior
Load-All guys and gals, the most common part you are going to lose is the sizing ring; hence, me looking at half a dozen Juniors and rejecting them because they were short the ring. I cut a half inch down and drilled a hole through it and then screwed it into the wooden base plate (right front corner). I never leave the press without ensuring that the ring is on the dowel.
Michael