Two powder questions
- rog54
- Posts: 21
- Joined: 01 Feb 2018 19:37
- My Press Choice: Single Stage
- Location: Geauga County, Ohio
- Has thanked: 1 time
- Been thanked: 2 times
Two powder questions
I have been using HP38 for my 9mm and 45acp loads. Is HP38 known as a "dirty" powder? Seems my guns have a good bit more mess. I have not had opportunity to compare to new ammo. Started using it because it was recommended by a local shop/reloader.
Secondly, Any of you loaded 357sig ? any recommendations on powder for that load?
Secondly, Any of you loaded 357sig ? any recommendations on powder for that load?
- mr surveyor
- Founding Member
- Posts: 650
- Joined: 30 Jun 2013 09:30
- My Press Choice: Hand Press
- Location: NE Texas
- Has thanked: 386 times
- Been thanked: 231 times
Re: Two powder questions
I've only dabbled with a bit of HP38, but I understand the claim of "dirty powder" .... same as Unique. I've use a good bit of Unique, but I did learn pretty early on that it needed to be loaded to the higher end of the spectrum - near (or at) the recommended max loads for it to get a good complete burn. My little bit of HP38 was used mainly in 38 spl, and was on the upper end of the standard .38 spl load recommendations. I never noticed excessive fouling with the more "upper end" loads. Same with Unique .... playing with the low end of the spectrum and I didn't get a good complete burn - gave the appearance of a "dirty powder". Loaded closer to the upper end and it not only cleaned up, it also tightened up the chrony statistics.
Try using the HP38 closer to the recommended "upper end" loads and see if it seems to clean up.
jd
Try using the HP38 closer to the recommended "upper end" loads and see if it seems to clean up.
jd
--------------------------------------------------------------------------------------
There's just some things best left unsaid on the internetsuperhighway.
There's just some things best left unsaid on the internetsuperhighway.
-
- Supporter
- Posts: 888
- Joined: 06 Mar 2016 16:09
- My Press Choice: Hand Press
- Location: SW Ohio
- Has thanked: 156 times
- Been thanked: 240 times
Re: Two powder questions
I've been using True Blue from Western Powders/Ramshot mostly with 90 and 110 grain jacketed and .1 to .2 above minimum with a tight tapper crimp. The H&K seems to like them.rog54 wrote:<snip>
Secondly, Any of you loaded 357sig ? any recommendations on powder for that load?
Make smoke,
Curt.......makin' smoke and raising my carbon foot print one cartridge at a time
-
- Founding Member & Supporter
- Posts: 674
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: S. Oregun
- Has thanked: 203 times
- Been thanked: 371 times
Re: Two powder questions
Almost any powder is "dirty" when not loaded to it's optimum level/pressure. Light loads of W231/HP38 will often leave a bit more debris, but mid to upper loads will burn "clean". One of my house gun loads is a 148 DEWC over near max/max loads of W231 for my 3" 38 Special. Clean burning, but as any thing that burns, it leaves some residue behind...
-
- Posts: 221
- Joined: 17 Mar 2014 10:13
- My Press Choice: Single Stage
- Location: N AL
- Has thanked: 12 times
- Been thanked: 76 times
Re: Two powder questions
HP38 is not even on my list for 45 ACP... maybe just me.
However, it seems to be the best so far with traditional older guns and loads for all the old guns/calibers I have/cast for/reload/shoot, including 32 S&W L, 38 SPC, 44-40, 45 Colt. Only one I have found it to be tad "dirty" is the 32 L, and, as just starting with that caliber/gun, I am attributing that to an inadequate roll crimp. More testing required. Also on the top of the list for my soon to have Old Colt 32-20.
However, it seems to be the best so far with traditional older guns and loads for all the old guns/calibers I have/cast for/reload/shoot, including 32 S&W L, 38 SPC, 44-40, 45 Colt. Only one I have found it to be tad "dirty" is the 32 L, and, as just starting with that caliber/gun, I am attributing that to an inadequate roll crimp. More testing required. Also on the top of the list for my soon to have Old Colt 32-20.
- GRV01
- Posts: 92
- Joined: 21 Mar 2017 02:14
- My Press Choice: Hand Press
- Location: Miami FL
- Has thanked: 6 times
- Been thanked: 24 times
Re: Two powder questions
I reload alot with HP38 for 38SPL, but i want to pick up 45ACP and 45LC and was hoping to continue using that powder for low poer plinkers. What is it about HP38 that keeps it out of your 45acp?oscarflytyer wrote:HP38 is not even on my list for 45 ACP... maybe just me.
No thin chicks
Currently reloading .357 Magnum and .38 Special
Currently reloading .357 Magnum and .38 Special
- GasGuzzler
- Moderator & Supporter
- Posts: 2045
- Joined: 26 Jan 2016 22:39
- My Press Choice: Turret
- Location: Cooke County, TX
- Has thanked: 330 times
- Been thanked: 501 times
Re: Two powder questions
Pretty sure I have a can of HP38. Not sure why I got it. It's the same as something else if memory serves.
The easiest cartridges to load for are .38 Special, .357 Magnum, .45 Colt, .45 ACP, 9mm and they can kind of use the same powder if you make large concessions.
The easiest cartridges to load for are .38 Special, .357 Magnum, .45 Colt, .45 ACP, 9mm and they can kind of use the same powder if you make large concessions.
__________________________________________________________________________________________
I've always been crazy but it's kept me from goin' insane.
I've always been crazy but it's kept me from goin' insane.
- Macd
- Supporter
- Posts: 1009
- Joined: 16 Oct 2017 16:12
- My Press Choice: Single Stage
- Location: Far East
- Has thanked: 362 times
- Been thanked: 403 times
Re: Two powder questions
As noted by miked above H38 is W231 according to Hogdon. I use W231 in 45 Colt, 45 Auto and in 38/357. If not loaded near max it tends to be dirty.
-
- Posts: 221
- Joined: 17 Mar 2014 10:13
- My Press Choice: Single Stage
- Location: N AL
- Has thanked: 12 times
- Been thanked: 76 times
Re: Two powder questions
A 4-5 grn Bullseye load with a 200 H&G #68 clone keeps pretty much any other powder/load out of my 45s. It just works so well, no reason or desire to play around...GRV01 wrote:I reload alot with HP38 for 38SPL, but i want to pick up 45ACP and 45LC and was hoping to continue using that powder for low poer plinkers. What is it about HP38 that keeps it out of your 45acp?oscarflytyer wrote:HP38 is not even on my list for 45 ACP... maybe just me.