Random Header Images
Forum rules
Keep it civil and mind the rules! Absolutely no ranting!
Keep it civil and mind the rules! Absolutely no ranting!
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2850 times
Random Header Images
I sure would like to start collecting images to replace the "stock" images in the Forum's random header at the top of every page. This has ended up working very well on my Rossi-Rifleman Forum but rifle images are a bit easier to capture.
Static images of the bench aren't very exciting, looking for some ideas. Ideally the pictures should be wider than they are tall, landscape. Any offerings or ideas?
Static images of the bench aren't very exciting, looking for some ideas. Ideally the pictures should be wider than they are tall, landscape. Any offerings or ideas?
Michael
-
- Founding Member
- Posts: 736
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: Kingsland, GA
- Has thanked: 51 times
- Been thanked: 222 times
Re: Random Header Images
This was loading 10mm for a Colt Delta Elite. Sorry about the RCBS green but they are the only loading blocks I have. Actually I'm not sure Lee has ever made loading blocks, have they???
And this was loading .223 and once again green is showing.
Perhaps some picture cropping?
And this was loading .223 and once again green is showing.
Perhaps some picture cropping?
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2850 times
Re: Random Header Images
They look good to me! I will put them in the mix in the morning and see how they sequence it. I will see what I have as well.
Michael
- akuser47
- Moderator & Supporter
- Posts: 1397
- Joined: 30 Jun 2013 09:16
- My Press Choice: Single Stage
- Location: ohio
- Has thanked: 666 times
- Been thanked: 266 times
Re: Random Header Images
Ok I'm in I was loading up some .357 mag with 158 grain XTP and 5.7 tightgroup almost finished only need to set half or more rounds and I rembered this thread so I even put a puter in with it to. lol
my humble submissions and messy workspace
Smokin Challenger press tried to have more fun don't remeber the tricks to the pics anymore but I liked this one. This is purely staged.
my humble submissions and messy workspace
Smokin Challenger press tried to have more fun don't remeber the tricks to the pics anymore but I liked this one. This is purely staged.
Last edited by akuser47 on 22 Aug 2013 18:45, edited 1 time in total.
-
- Founding Member
- Posts: 736
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: Kingsland, GA
- Has thanked: 51 times
- Been thanked: 222 times
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2850 times
Re: Random Header Images
The nice addition is "Lee Loader" being on the screen!
Here is what the pictures are going to look like to in order to fit the formatting of the header...
Might be too much detail in the typical bench picture with the confines of the image size Pretty busy...
Here is what the pictures are going to look like to in order to fit the formatting of the header...
Might be too much detail in the typical bench picture with the confines of the image size Pretty busy...
You do not have the required permissions to view the files attached to this post.
Michael
- akuser47
- Moderator & Supporter
- Posts: 1397
- Joined: 30 Jun 2013 09:16
- My Press Choice: Single Stage
- Location: ohio
- Has thanked: 666 times
- Been thanked: 266 times
Re: Random Header Images
I staged the laptop it is normally on my desk. The great value container has used razor blades in it great value can has loose screws. I guess I should have just taken a shot of my press and such I got carried away.
- joec
- Founding Member
- Posts: 78
- Joined: 30 Jun 2013 09:25
- My Press Choice: Turret
- Location: Lexington Kentucky
- Been thanked: 12 times
Re: Random Header Images
You asked for images here are some from me and the Lee Reloader press is now living with my BIL. Oh and it was setup to do my Magtech shot shells in the picture however that job is now being done with RCBS Cowboy die for the same shell on a Lee Classic Cast.
Next is my Lee Perfect Powder measure mounted for 45-70 Gov.
Last how I store my turrets with powder measures. I have 9mm, 45 ACP, 2 for 45 Colt, 454 Casull and 1 turret for additional crimp dies and of course the 45-70 Gov. Shown are the 45 ACP and 45-70 turrets.
You do not have the required permissions to view the files attached to this post.
Joe
- Steelbanger
- Founding Member
- Posts: 59
- Joined: 30 Jun 2013 10:12
- My Press Choice: Single Stage
- Location: Pennsylvania U.S.A.
- Has thanked: 16 times
- Been thanked: 24 times
Re: Random Header Images
Hey Maximumbob54,Maximumbob54 wrote:This was loading 10mm for a Colt Delta Elite. Sorry about the RCBS green but they are the only loading blocks I have. Actually I'm not sure Lee has ever made loading blocks, have they???
This is what shows on my monitor so maybe Lee did make loading blocks.
You do not have the required permissions to view the files attached to this post.
-
- Founding Member
- Posts: 736
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: Kingsland, GA
- Has thanked: 51 times
- Been thanked: 222 times
Re: Random Header Images
That would rock!!!Steelbanger wrote:Hey Maximumbob54,Maximumbob54 wrote:This was loading 10mm for a Colt Delta Elite. Sorry about the RCBS green but they are the only loading blocks I have. Actually I'm not sure Lee has ever made loading blocks, have they???
This is what shows on my monitor so maybe Lee did make loading blocks.