Yes I would also like to have it. I use Open Office all the time.Old Scribe wrote:Nice spreadsheet. I'd be happy to to get it. I use Open Office a lot-find it a good program.
Autodisk Size Selection
- Macd
- Supporter
- Posts: 1009
- Joined: 16 Oct 2017 16:12
- My Press Choice: Single Stage
- Location: Far East
- Has thanked: 362 times
- Been thanked: 403 times
Re: Autodisk Size Selection
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
- Old Scribe
- Supporter
- Posts: 369
- Joined: 02 May 2015 09:13
- My Press Choice: Turret
- Location: State of Jefferson
- Has thanked: 461 times
- Been thanked: 120 times
Re: Autodisk Size Selection
Thanks!
"Well here's another nice mess you've gotten me into." Oliver Hardy
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: Autodisk Size Selection
You're welcome guys. Once you determine the actual VMD of your powders, it will be a useful tool.
Michael
-
- Supporter
- Posts: 1006
- Joined: 09 Nov 2015 06:35
- My Press Choice: Single Stage
- Location: Washington State
- Has thanked: 38 times
- Been thanked: 274 times
Re: Autodisk Size Selection
Ranch Dog wrote:I have ten small jugs of Trail Boss, I hope to find someone with something to trade for it one day.
I wish I lived close by. I'm sure we could find SOMETHING to trade.... I know it's not for everybody but I like that stuff...
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
- GasGuzzler
- Moderator & Supporter
- Posts: 2046
- Joined: 26 Jan 2016 22:39
- My Press Choice: Turret
- Location: Cooke County, TX
- Has thanked: 330 times
- Been thanked: 501 times
Re: Autodisk Size Selection
Pour it all in a flour sack and use it as a pillow.
__________________________________________________________________________________________
I've always been crazy but it's kept me from goin' insane.
I've always been crazy but it's kept me from goin' insane.
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: Autodisk Size Selection
For my dogs...GasGuzzler wrote:Pour it all in a flour sack and use it as a pillow.
I boxed it up today. I have nine, unopened 9 ounces jugs and the tenth jug has a bit over 6 ounces. All jugs are the same lot number, so a bit over 5 lbs of it. Might check into HAZMAT and shipping.
The only application I have personally found for it is my 218 Bee as a 22 rimfire replacement. I use it in my yard for night time critters that are digging or bugging me. The problem is charging a 22 caliber case neck with the Trail Boss donuts, it is a very slow process, and I'm not interested in any slow reloading.
Going to try a light load of Clays today. 3-grains should produce 1500 FPS with my TLC225-50-RF. It has a very low case fill, so I'm going to try it on its own and as a duplex with BPI Buffer. I will open a new topic with that shooting, but if all goes well, I will see about moving the powder. I've asked around here, but no one "plinks." Plinking in South Texas is hammering hogs.
Michael
- Macd
- Supporter
- Posts: 1009
- Joined: 16 Oct 2017 16:12
- My Press Choice: Single Stage
- Location: Far East
- Has thanked: 362 times
- Been thanked: 403 times
Re: Autodisk Size Selection
Tried the VMD calculator for Win231 in 38 special. It said use the .37 orifice and sure enough it gave me exactly the 4.0 grains I wanted. If you were close Mike I would buy you a beer assuming you imbibe the golden nectar.