Nickel-plated cases?
-
- Posts: 26
- Joined: 24 Nov 2019 19:53
- My Press Choice: Lee Loader
- Location: Harrisburg, PA
- Has thanked: 20 times
- Been thanked: 12 times
Nickel-plated cases?
Hi all,
Quick question: is there any issue reloading nickel-plated cases in a Lee Loader?
Thanks,
-Drew
Quick question: is there any issue reloading nickel-plated cases in a Lee Loader?
Thanks,
-Drew
-
- Posts: 26
- Joined: 01 Nov 2019 21:45
- My Press Choice: Progressive
- Location: Union MS
- Been thanked: 8 times
Re: Nickel-plated cases?
I have had no issues in any lee loader with plated cases. I have had issues with NP cases not holding a crimp as well with 40 or 45. In 25 to 9mm , how ever it seems to have no effect on crimp. One of the old guys may have more revelation?
-
- Posts: 26
- Joined: 01 Nov 2019 21:45
- My Press Choice: Progressive
- Location: Union MS
- Been thanked: 8 times
Re: Nickel-plated cases?
By the way Lufbery I’m only approaching the big 50 , loading since the 90’s. You have guys on here loading when I was a kid. You asked the right guys!
-
- Founding Member & Supporter
- Posts: 1123
- Joined: 20 Dec 2013 11:09
- My Press Choice: Single Stage
- Location: Arizona
- Location: Arizona
- Has thanked: 688 times
- Been thanked: 327 times
Re: Nickel-plated cases?
Never had a problem with plated cases holding a crimp in 38spec, because everything
I loaded was cast, usually 148gr button nose wad cuters.
Have had some trouble with plated cases in ground pounder H110 & heavy XTP's hunting loads in .357 holding a crimp?? & I do not get shy about crimping...
Never had a problem with brass??
You'll be ok with with plated in your Lee Loader. If I find any with the plating
Coming off, I toss 'em, but thats just me..
" OLD GUYS " ??? I resemble that remark dude.. Besides that, your not that far
behind !!!!
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
I loaded was cast, usually 148gr button nose wad cuters.
Have had some trouble with plated cases in ground pounder H110 & heavy XTP's hunting loads in .357 holding a crimp?? & I do not get shy about crimping...
Never had a problem with brass??
You'll be ok with with plated in your Lee Loader. If I find any with the plating
Coming off, I toss 'em, but thats just me..
" OLD GUYS " ??? I resemble that remark dude.. Besides that, your not that far
behind !!!!
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
A day late & A dollar short? Story of my life ![Shoot'em Up +guns](./images/smilies/icon_guntootsmiley.gif)
![Shoot'em Up +guns](./images/smilies/icon_guntootsmiley.gif)
-
- Supporter
- Posts: 888
- Joined: 06 Mar 2016 16:09
- My Press Choice: Hand Press
- Location: SW Ohio
- Has thanked: 156 times
- Been thanked: 240 times
Re: Nickel-plated cases?
Having reach 3/4 of a century last August and a reloader since '67 (19) I guess I can qualify as an old guy. I shot a lot of plated 357 in my Contender back when the 357 barrel was my production jun in IHMSA shooting, heavy bullets and heavy charges of H110. I'd start seeing mouth cracks at the 4th or 5th loading and after 6 or so the plating would start coming off. I always blamed it on the heavy charges until I switched to plain brass and was getting anywhere from 8 to 10 loadings and usually by then the primer pockets were getting loose and I'd start with a new batch of cases. The plated cases always "felt" harder to me when they were being resized. Just the sense that it took more muscle to size them.
Since I bought the Rossi '92 in 357 I've dug out some of those left over cases and after one medium hot loading the remaing plated cases went in the trash. Some of the older plain brass are still going strong.
A lot of this is highly subjective so take as intended as observations comparing plated to plain in my guns and my loads.
Make smoke and happy Thanksgiving,
Since I bought the Rossi '92 in 357 I've dug out some of those left over cases and after one medium hot loading the remaing plated cases went in the trash. Some of the older plain brass are still going strong.
A lot of this is highly subjective so take as intended as observations comparing plated to plain in my guns and my loads.
Make smoke and happy Thanksgiving,
Curt.......makin' smoke and raising my carbon foot print one cartridge at a time
![Shoot'em Up +guns](./images/smilies/icon_guntootsmiley.gif)
![Shoot'em Up +guns](./images/smilies/icon_guntootsmiley.gif)
![Shoot'em Up +guns](./images/smilies/icon_guntootsmiley.gif)
-
- Founding Member & Supporter
- Posts: 674
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: S. Oregun
- Has thanked: 203 times
- Been thanked: 371 times
Re: Nickel-plated cases?
When I started reloading 38 Special in '69, I gleaned some brass from the local police range, and about 50% were nickel plated 38 and 357 Magnum. Since that time I have been reloading nickel plated handgun brass (and a very few .223) using the same methods as plain nekkid brass cases. I have not experienced the "shorter case life" nor flaking or "harder resizing". I have reloaded some 38 cases so many times the plating has worn and brass shows through...
I have some Federal nickel plated 44 Magnum brass that I keep separate for my T-Rex Killer loads (265 gr RNFP over max loads of WC820) and now have 6 reloadings on them and they look brand new...
I have some Federal nickel plated 44 Magnum brass that I keep separate for my T-Rex Killer loads (265 gr RNFP over max loads of WC820) and now have 6 reloadings on them and they look brand new...
- Macd
- Supporter
- Posts: 1009
- Joined: 16 Oct 2017 16:12
- My Press Choice: Single Stage
- Location: Far East
- Has thanked: 362 times
- Been thanked: 403 times
Re: Nickel-plated cases?
Use NP in 308, 45 Auto and 38/357. Can't say I have noticed any difference from brass except they look prettier on the gun belt.
-
- Posts: 26
- Joined: 01 Nov 2019 21:45
- My Press Choice: Progressive
- Location: Union MS
- Been thanked: 8 times
Re: Nickel-plated cases?
I knew you would like the old guy comment! LOL I agree with the limited life of NP as well. Thought it was just me. Never loaded much 38 , good knowledge to store. Thanks happy thanksgiving everyone!
-
- Posts: 26
- Joined: 01 Nov 2019 21:45
- My Press Choice: Progressive
- Location: Union MS
- Been thanked: 8 times
Re: Nickel-plated cases?
Keep in mind guys I even at my age ( ha ha) I still shoot competitions. Head to head often. So I load quantities not for pounding. I get on average over recommended loading on case. But I do keep lot numbers. 12 to 15 cycles is average at moderate pressures . If power factor is a requirement I will use once fired brass. After 12 to 15 cycles you feel primer pocket swelling, depending on quality of brass manufacturer. I agree it is depending on quality of brass , cycles reloaded , and pressure. All good info.
-
- Supporter
- Posts: 888
- Joined: 06 Mar 2016 16:09
- My Press Choice: Hand Press
- Location: SW Ohio
- Has thanked: 156 times
- Been thanked: 240 times
Re: Nickel-plated cases?
You can also add in chamber size and head space. If the cases are "swelling" or stretching due to chamber dimensions you'll have shorter case life.
Make smoke,
Make smoke,
Curt.......makin' smoke and raising my carbon foot print one cartridge at a time
![Shoot'em Up +guns](./images/smilies/icon_guntootsmiley.gif)
![Shoot'em Up +guns](./images/smilies/icon_guntootsmiley.gif)
![Shoot'em Up +guns](./images/smilies/icon_guntootsmiley.gif)