berry's bullets
-
- Posts: 25
- Joined: 23 Dec 2018 08:56
- My Press Choice: Single Stage
- Location: New England
- Been thanked: 1 time
berry's bullets
I'd like to substitue a 125gr berry's plated bullet for a 125gr hornady hp/xtp bullet. I've heard that you can use a berry's bullet in place of a jacketed bullet as long as you keep to the starting powder load. I'd be obliged if anyone here who uses berry's bullets can offer some insight.
- mr surveyor
- Founding Member
- Posts: 650
- Joined: 30 Jun 2013 09:30
- My Press Choice: Hand Press
- Location: NE Texas
- Has thanked: 386 times
- Been thanked: 231 times
Re: berry's bullets
and what caliber and what desired velocity?
The plated bullets are rated by the manufacturer (Berry's, X-Treme, etc) for a specific maximum velocity (for their particular bullet). As long as your load stays within their stated velocity range, and you don't unduly cut/damage the plating while loading/crimping, you should do fine. I've only loaded about 1k each of plated bullets in the 9mm and .45 acp semi-auto rounds, but still have had no issues while staying within the bullet manufacturers stated velocities.
jd
The plated bullets are rated by the manufacturer (Berry's, X-Treme, etc) for a specific maximum velocity (for their particular bullet). As long as your load stays within their stated velocity range, and you don't unduly cut/damage the plating while loading/crimping, you should do fine. I've only loaded about 1k each of plated bullets in the 9mm and .45 acp semi-auto rounds, but still have had no issues while staying within the bullet manufacturers stated velocities.
jd
--------------------------------------------------------------------------------------
There's just some things best left unsaid on the internetsuperhighway.
There's just some things best left unsaid on the internetsuperhighway.
-
- Posts: 25
- Joined: 23 Dec 2018 08:56
- My Press Choice: Single Stage
- Location: New England
- Been thanked: 1 time
Re: berry's bullets
Berrys recommends staying below 1,250 fps. I want to substitute berrys 125 gr bullets for hornady hp/xtp bullets in .38 spl, using Universal powder at a starting load of 4.7 grains.
-
- Supporter
- Posts: 888
- Joined: 06 Mar 2016 16:09
- My Press Choice: Hand Press
- Location: SW Ohio
- Has thanked: 156 times
- Been thanked: 240 times
Re: berry's bullets
I've used Berrys in 9mm, 380, 45 ACP, 45 Colt and 357 Sig. I used starting jacket loads for the bullet weight and worked up in tenth (0.1) grain increments to either best accuracy or the accuracy going to hell. When the plating starts giving up it'll let you know. I've also done the same with Rainer bullets but only in the 45 Colt. These are all taper crimped to not damage the plating. Lee's factory crimp die will also work.
Make smoke,
Make smoke,
Curt.......makin' smoke and raising my carbon foot print one cartridge at a time
-
- Supporter
- Posts: 1001
- Joined: 09 Nov 2015 06:35
- My Press Choice: Single Stage
- Location: Washington State
- Has thanked: 38 times
- Been thanked: 274 times
Re: berry's bullets
[quote="bluetick"]Berrys recommends staying below 1,250 fps. I want to substitute berrys 125 gr bullets for hornady hp/xtp bullets in .38 spl, using Universal powder at a starting load of 4.7 grains.[/quote
That should be in the 900fps range so it would seem to fall within the parameters of which you seek.....I've never used Berrys bullets but have shot a lot of RMR plated bullets in 9mm at close to 1300fps with no issues. IIRC RMR advertises their bullets as double plated and the core is 12 BHn which is a pretty hard lead.
That should be in the 900fps range so it would seem to fall within the parameters of which you seek.....I've never used Berrys bullets but have shot a lot of RMR plated bullets in 9mm at close to 1300fps with no issues. IIRC RMR advertises their bullets as double plated and the core is 12 BHn which is a pretty hard lead.
- JohnnyEnfield
- Supporter
- Posts: 159
- Joined: 08 Dec 2017 20:24
- My Press Choice: Single Stage
- Location: Northeast USA
- Has thanked: 176 times
- Been thanked: 53 times
Re: berry's bullets
I have used Berry's in 9mm and .45 Auto. Yes, the lower end load data for weight in jacketed "should be ok". In my experience they are good if you keep the velocity lower, like you are supposed to. I have tried a few different things and prefer lead cast (either powder coated or Hi-Tech coated) bullets now to plated. The lead seems more accurate to me. As always, be careful and work up. As Ohio3Wheels stated, once they get screwy it is time to back off, they will get screwy if run too hard. Good luck. Be safe.
Reduce, reuse, recycle, means- resize, reload, recycle.
- GasGuzzler
- Moderator & Supporter
- Posts: 2044
- Joined: 26 Jan 2016 22:39
- My Press Choice: Turret
- Location: Cooke County, TX
- Has thanked: 330 times
- Been thanked: 501 times
Re: berry's bullets
I use them for 9mm (as well as cast). I don't know the velocity and my load is at least in the middle of jacketed but I run long OAL and a little extra Bullseye on the load I developed specifically for my P95. I've never shot hand loaded ammo in my Shield. I use cast or jacketed for .45 AUTO so far and ALL lead for .45 Colt, .38, and .357.
I'm not familiar with Universal and I don't load the .38 that far under-weight (80% of design) but it sounds fine. I would recommend the Lee crimp die regardless of bullet type.
I'm not familiar with Universal and I don't load the .38 that far under-weight (80% of design) but it sounds fine. I would recommend the Lee crimp die regardless of bullet type.
__________________________________________________________________________________________
I've always been crazy but it's kept me from goin' insane.
I've always been crazy but it's kept me from goin' insane.