I started having a problem (several actually) when casting recently. Maybe from too hot of an alloy and maybe from too much pressure or both. The thing I am asking about specifically is a problem with the base on some of the bullets having "fins" or little spots of alloy sticking off. I never had them like this before. I am attaching a picture to ask for your opinion on what caused it and what I can do about it. There were a lot of good bullets cast too, the ones in the picture were the worst. Thank you.
Bullet casting "Fins"
- JohnnyEnfield
- Supporter
- Posts: 159
- Joined: 08 Dec 2017 20:24
- My Press Choice: Single Stage
- Location: Northeast USA
- Has thanked: 176 times
- Been thanked: 53 times
Bullet casting "Fins"
You do not have the required permissions to view the files attached to this post.
Reduce, reuse, recycle, means- resize, reload, recycle.
-
- Supporter
- Posts: 888
- Joined: 06 Mar 2016 16:09
- My Press Choice: Hand Press
- Location: SW Ohio
- Has thanked: 156 times
- Been thanked: 240 times
Re: Bullet casting "Fins"
Usually when I see that sort of thing I find the sprue plate has gotten loose enough that it's letting alloy squeeze out under it. A warped sprue plate can also cause that to happen.
Make smoke,
Make smoke,
Curt.......makin' smoke and raising my carbon foot print one cartridge at a time
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2850 times
-
- Founding Member & Supporter
- Posts: 1123
- Joined: 20 Dec 2013 11:09
- My Press Choice: Single Stage
- Location: Arizona
- Location: Arizona
- Has thanked: 688 times
- Been thanked: 327 times
Re: Bullet casting "Fins"
Ohio3Wheels wrote:Usually when I see that sort of thing I find the sprue plate has gotten loose enough that it's letting alloy squeeze out under it. A warped sprue plate can also cause that to happen.
Make smoke,
My experience in casting is very limited to most on this site but, I immediately thought the
same as Wheels, loose or warped plate.
A day late & A dollar short? Story of my life
- JohnnyEnfield
- Supporter
- Posts: 159
- Joined: 08 Dec 2017 20:24
- My Press Choice: Single Stage
- Location: Northeast USA
- Has thanked: 176 times
- Been thanked: 53 times
Re: Bullet casting "Fins"
Funny thing is the same casting session the .358 158 grain TL SWC sprue plate was giving me fits. the sprue plate on this mold (TL230RN) seems fine, operated well and stayed tight. I had to stop using the other mold bc it was just not helpful messing with it so I kept casting with the one mold. I had seen a few tiny specs form from time to time with this bullet but these ones were bad. Once the last one on the right happened, I just called it a night and started cleaning up. I will have to clean the sprue plate and see how it goes next time. In the meantime I need to figure out what is going on with my other mold that actually seems like the sprue plate it messed up. When I tighten it all the way where I want it, it lifts up and its not flat. The sprue plate for these bullets seems really flat and flush. Just odd. I thought the force of pressure of hot liquid was backing it out a bit under the plate maybe. Have to start fresh in a few days when the weather clears I guess. Thanks for chiming in guys.
Reduce, reuse, recycle, means- resize, reload, recycle.
- Macd
- Supporter
- Posts: 1009
- Joined: 16 Oct 2017 16:12
- My Press Choice: Single Stage
- Location: Far East
- Has thanked: 362 times
- Been thanked: 403 times
Re: Bullet casting "Fins"
It would be great to see pictures of the top of your mould with the plate opened and closed but here are my thoughts. I am assuming Lee moulds.
1. Loose sprue plate. Once they are loose they can be tough to keep tight without adding a lock screw. Don't over tighten.
2. Galling under the spruce at the hinge. This is usually caused by no lubrication. I use beeswax but any wax works. Just don't let it get into cavities.
3. Mould block vertical mis-alignment. If one block is lower than the other or blocks don't align firmly allowing galling or on one to push them out of alignment then finning over I suppose the lower block is possible. Over tightening the handle bolt can also cause alignment problems. The obvious check is whether rings/grooves line up on bullet.
4. Wiping caused by sprue not being cooled enough. Your bullets don't look frosted so this would be likely a really hot mould. I have had this happen to me when I first started casting. I am not sure if the blocks or plate were the hotter part of the mould. I was pouring sprues that almost covered the plate.
1. Loose sprue plate. Once they are loose they can be tough to keep tight without adding a lock screw. Don't over tighten.
2. Galling under the spruce at the hinge. This is usually caused by no lubrication. I use beeswax but any wax works. Just don't let it get into cavities.
3. Mould block vertical mis-alignment. If one block is lower than the other or blocks don't align firmly allowing galling or on one to push them out of alignment then finning over I suppose the lower block is possible. Over tightening the handle bolt can also cause alignment problems. The obvious check is whether rings/grooves line up on bullet.
4. Wiping caused by sprue not being cooled enough. Your bullets don't look frosted so this would be likely a really hot mould. I have had this happen to me when I first started casting. I am not sure if the blocks or plate were the hotter part of the mould. I was pouring sprues that almost covered the plate.