Cleaning and polishing brass
Cleaning and polishing brass
Another question that I have is, is there anything that I can add to my walnut shells in the vibrating tumbler to polish my brass? I am using 24 grit walnut shells clean them. Coming out pretty clean, but want to polish also. Any tricks? Hate to have to use walnut shells to clean, then have to change everything and reload tumbler with corncob .
- daboone
- Founding Member
- Posts: 1397
- Joined: 30 Nov 2013 21:47
- My Press Choice: Single Stage
- Location: AZ, TX, HI
- Has thanked: 677 times
- Been thanked: 787 times
Re: Cleaning and polishing brass
NuFinish is a liquid car wax that is popularly use by many. I've read that NuFinish is made up of zinc polymer emulsions that's not like most other car polishes which makes it uniquely good for brass. Add a couple of cap fulls and then run your buzz bucket for 30 minutes to get it mixed in before adding brass. I prefer to mix it 50/50 with mineral spirits (MS) but I live alone so nobody complains about the smell. The MS just make the dispersion faster. I find after 4 batches another capful full is needed.
An ignorant person is one who doesn't know what you have just found out.
When setting a job up for myself it must be Idiot Proof as well, as I am a bigger idiot than most people I know, and I prove it to myself everyday.
When setting a job up for myself it must be Idiot Proof as well, as I am a bigger idiot than most people I know, and I prove it to myself everyday.
-
- Posts: 20
- Joined: 10 Feb 2014 09:10
- My Press Choice: Progressive
- Location: ft bragg nc
- Been thanked: 3 times
Re: Cleaning and polishing brass
Sorry, but l use Stainless media.
Vibrator w/lizard litter & polish l would like to have after brass comes out of ss.
I made this from youtube: love it.
Directions:
Vibrator w/lizard litter & polish l would like to have after brass comes out of ss.
I made this from youtube: love it.
Directions:
-
- Posts: 4
- Joined: 30 Jun 2013 09:18
- My Press Choice: Progressive
- Location: Midland, TX
Re: Cleaning and polishing brass
Best process I've found is to soak brass in plastic bucket with solution of hot citric acid. Then rinse thoroughly, dry, & then tumble. Brass comes out clean with nice shiny finish. Also, the citric acid solution passavates the brass making it resistant to tarnishing. The solution is reusable. Heating the solution just makes it work faster. It only takes a about 5 minutes soaking to clean and remove the tarnish with the solution at near boiling. The solution react with other metals so heat it & store it in plastic or microwaveable glass. You can get citric acid in powder form on the EBay pretty cheap or merely buy Lemishine dishwasher additive. It's almost entirely citric acid. Add about 3 tablespoon per gallon of hot water.
-
- Founding Member
- Posts: 736
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: Kingsland, GA
- Has thanked: 51 times
- Been thanked: 222 times
Re: Cleaning and polishing brass
You can also buy citric acit anywhere they market jarring and canning supplies. Or if you want a lifetime supply you can go to a feed store and buy the bags of it they use as feed suplement.
-
- Founding Member & Supporter
- Posts: 1123
- Joined: 20 Dec 2013 11:09
- My Press Choice: Single Stage
- Location: Arizona
- Location: Arizona
- Has thanked: 688 times
- Been thanked: 327 times
Re: Cleaning and polishing brass
All excellent info. If using citric acid, don't soak for to long, it will react with, & remove zinc from the brass alloy & turn it a pretty pink. Lemi-Shine is a great & useful product, you can also get the citric acid in cheap, generic lemonade powder, the kind in the little packets.
A day late & A dollar short? Story of my life
-
- Founding Member & Supporter
- Posts: 674
- Joined: 30 Jun 2013 09:30
- My Press Choice: Turret
- Location: S. Oregun
- Has thanked: 203 times
- Been thanked: 371 times
Re: Cleaning and polishing brass
Walnut is a bit more aggressive than corn cob media and won't give the high gloss shine that can be achieved with corn cob media with a touch of auto polish...
Over the last few years I've been K.I.S.S.ing my brass cleaning. I'm using a 50/50 mixture of course grind walnut hulls and corn cob blast media.. I have no need for pristine primer pockets and a semi-glossy shine is enough for me to find my brass in the dirt/grass where I shoot...
Over the last few years I've been K.I.S.S.ing my brass cleaning. I'm using a 50/50 mixture of course grind walnut hulls and corn cob blast media.. I have no need for pristine primer pockets and a semi-glossy shine is enough for me to find my brass in the dirt/grass where I shoot...
Last edited by mikld on 03 May 2014 11:44, edited 3 times in total.
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: Cleaning and polishing brass
I still prefer the washing machine method.
This highly glossy shine from acid and polish isn't necessary, and the baked on graphite actually doubles as a dry lubricant for sizing dies.
This highly glossy shine from acid and polish isn't necessary, and the baked on graphite actually doubles as a dry lubricant for sizing dies.
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- mr surveyor
- Founding Member
- Posts: 650
- Joined: 30 Jun 2013 09:30
- My Press Choice: Hand Press
- Location: NE Texas
- Has thanked: 386 times
- Been thanked: 231 times
Re: Cleaning and polishing brass
I don't think my brass has any zinc in it. It does have Tin in the alloy, and ammonia reacts with the tin, but I don't use anything but mild acids to thoroughly clean my brass (either vinegar or citric acid .... Lemi-Shine) and they do not contain ammonia. I have noticed a few pieces of brass come out of the wash with a pink hue though and would very much like to know the answer for that from a metallurgist. I'm not into polished brass, but I do like it clean - inside and out (including the primer pocket and flash hole).
JD
JD
--------------------------------------------------------------------------------------
There's just some things best left unsaid on the internetsuperhighway.
There's just some things best left unsaid on the internetsuperhighway.
- wscywabbit
- Founding Member
- Posts: 53
- Joined: 04 Dec 2013 15:19
- My Press Choice: Turret
- Location: Washington State
- Has thanked: 13 times
- Been thanked: 16 times
Re: Cleaning and polishing brass
I use a water/vinegar/soap/salt mix that works pretty well to get the brass clean, but if you leave it too long it does turn some of the brass pink. ..
In God and guns we trust; it's an American tradition!