Perfect Powder Measure Powder Spill Tray
Forum rules
Remember that this forum is not associated with Lee Precision, this is just a customer based discussion of product ideas.
Remember that this forum is not associated with Lee Precision, this is just a customer based discussion of product ideas.
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Perfect Powder Measure Powder Spill Tray
We all know that even a lapped Perfect Powder Measure is bound to spill just a bit of powder, the amount depending on the type of powder. It has never bothered me on the bench mount, but in that, I have started using the PPM with the Gun Guide's Adapter directly on the Powder Through Expander Die or the Lee Short/Long Rifle Charging Die, it does. Plus in either case, I would like to try to recover the spilled powder.
As I started to reload yesterday morning, I watch just a few specks of H110 falling onto the white Safety Prime mount and immediately envisioned a tray of similar shape that mounts on the base of the PPM. It would keep your bench or turret head clean and allow the recovery of the powder. It would need to keep clear of the handle on one side and then be able to keep clear of the bullet seating die as well for use with a turret head. Not having a 3D printer, I immediately pressed a mailer tube end cap into service!
The powder debris on the turret head is primarily what landed prior to using the catch tray. After installation of the tray, the spill onto the turret head was nil. The spill is negligible and typical. After thirty drops I dumped the spilled powder into the scale pan and it weighed 2.5 grains, less than a tenth of a grain per drop.
I sent this to Dennis at Titan, don't know if he would pursue it as a 3D printed item for sale or not. I'm not going to get into the 3D stuff. I might use the other end cap to make another with the hole off center so that more area is available on the spill side of the tray plus I will keep my eye out for any other shaped part that might work.
As I started to reload yesterday morning, I watch just a few specks of H110 falling onto the white Safety Prime mount and immediately envisioned a tray of similar shape that mounts on the base of the PPM. It would keep your bench or turret head clean and allow the recovery of the powder. It would need to keep clear of the handle on one side and then be able to keep clear of the bullet seating die as well for use with a turret head. Not having a 3D printer, I immediately pressed a mailer tube end cap into service!
The powder debris on the turret head is primarily what landed prior to using the catch tray. After installation of the tray, the spill onto the turret head was nil. The spill is negligible and typical. After thirty drops I dumped the spilled powder into the scale pan and it weighed 2.5 grains, less than a tenth of a grain per drop.
I sent this to Dennis at Titan, don't know if he would pursue it as a 3D printed item for sale or not. I'm not going to get into the 3D stuff. I might use the other end cap to make another with the hole off center so that more area is available on the spill side of the tray plus I will keep my eye out for any other shaped part that might work.
Michael
- buckeye43210
- 250 Shots
- Posts: 253
- Joined: 20 Dec 2014 09:47
- My Press Choice: Progressive
- Location: TPA
- Has thanked: 23 times
- Been thanked: 131 times
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: Perfect Powder Measure Powder Spill Tray
Just don't have the time.buckeye43210 wrote:You could easily design this using OpenSCAD...
Michael
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
Re: Perfect Powder Measure Powder Spill Tray
Yeah, a step drill. Just cut real slow speed. I look at the drill bit and get back with the size of hole needed.farmerjim wrote:Did you make the hole in it with a drill ?
Michael
- buckeye43210
- 250 Shots
- Posts: 253
- Joined: 20 Dec 2014 09:47
- My Press Choice: Progressive
- Location: TPA
- Has thanked: 23 times
- Been thanked: 131 times
Re: Perfect Powder Measure Powder Spill Tray
What's the diameter of the hole?Ranch Dog wrote:Yeah, a step drill. Just cut real slow speed. I look at the drill bit and get back with the size of hole needed.farmerjim wrote:Did you make the hole in it with a drill ?
- Ranch Dog
- Site Admin
- Posts: 6458
- Joined: 22 Jun 2013 17:16
- My Press Choice: Progressive
- Location: Inez, TX
- Has thanked: 1617 times
- Been thanked: 2851 times
- buckeye43210
- 250 Shots
- Posts: 253
- Joined: 20 Dec 2014 09:47
- My Press Choice: Progressive
- Location: TPA
- Has thanked: 23 times
- Been thanked: 131 times
Re: Perfect Powder Measure Powder Spill Tray
Thanks for the idea. Here's the 3D model of your spill tray.
You do not have the required permissions to view the files attached to this post.