.380 with 80gr bullet
-
- Posts: 34
- Joined: 30 Jun 2013 09:20
- My Press Choice: Single Stage
- Location: S. MN
- Has thanked: 1 time
- Been thanked: 12 times
.380 with 80gr bullet
I picked up a box of super vel 80gr JHP at a gun shop. Only load that I can find is for a 80gr solid bullet in Lee's load manual. It has min 3.6 max 4.0 of No. 5. Will I be safe with 3.6gr to start?
-
- Founding Member & Supporter
- Posts: 1099
- Joined: 21 Jan 2014 20:57
- My Press Choice: Progressive
- Location: Eastern Iowa
- Has thanked: 182 times
- Been thanked: 357 times
Re: .380 with 80gr bullet
That would be their suggested starting load. Should be plenty safe, but may not have enough power to function the pistol properly.
The last time I tried a light load 380 in my Glock it malfunctioned quite a bit. I realized the load was just barely strong enough and I was limp wristing a bit. So it told me to get back to basics for a while, I did and my shooting improved. Did not load anymore 380s with that load.
The last time I tried a light load 380 in my Glock it malfunctioned quite a bit. I realized the load was just barely strong enough and I was limp wristing a bit. So it told me to get back to basics for a while, I did and my shooting improved. Did not load anymore 380s with that load.
-
- Supporter
- Posts: 888
- Joined: 06 Mar 2016 16:09
- My Press Choice: Hand Press
- Location: SW Ohio
- Has thanked: 156 times
- Been thanked: 240 times
Re: .380 with 80gr bullet
As long as the bearing surfaces of the two are close the starting load shouldn't cause you any problems. I didn't know SuperVel was still around. I used some of there stuff in 9mm a lot of years ago.
Make smoke,
Make smoke,
Curt.......makin' smoke and raising my carbon foot print one cartridge at a time
-
- Supporter
- Posts: 1002
- Joined: 09 Nov 2015 06:35
- My Press Choice: Single Stage
- Location: Washington State
- Has thanked: 38 times
- Been thanked: 274 times
Re: .380 with 80gr bullet
The only difference in load data would probably be the OAL...check the bullets for length comparison.
- GasGuzzler
- Moderator & Supporter
- Posts: 2044
- Joined: 26 Jan 2016 22:39
- My Press Choice: Turret
- Location: Cooke County, TX
- Has thanked: 330 times
- Been thanked: 501 times
Re: .380 with 80gr bullet
No .380 for me but I've done two rounds with 9mm and won. First round fail was because of under-powered loads....and first round for me was in single action! Should have been a simple fix but I got %@*&$ off and sold all my factory 9mm, all my brass, my dies, and all my jacketed loose projectiles. When I bought a P95 I had more loading experience and less fear. 9mm runs like a top now.
Fear not.
Fear not.
__________________________________________________________________________________________
I've always been crazy but it's kept me from goin' insane.
I've always been crazy but it's kept me from goin' insane.
-
- Founding Member & Supporter
- Posts: 1099
- Joined: 21 Jan 2014 20:57
- My Press Choice: Progressive
- Location: Eastern Iowa
- Has thanked: 182 times
- Been thanked: 357 times
Re: .380 with 80gr bullet
I feed the same 380 cartridge to 3 of me and my Daughter's 380s. I just keep the OAL under max, make sure they feed well, and shoot reasonably accurate.Horseman wrote:The only difference in load data would probably be the OAL...check the bullets for length comparison.
By some stroke of luck the load I practice with shoots very close to the Hornady Critical Defense round I carry.
-
- Posts: 34
- Joined: 30 Jun 2013 09:20
- My Press Choice: Single Stage
- Location: S. MN
- Has thanked: 1 time
- Been thanked: 12 times
Re: .380 with 80gr bullet
I might just keep the box on the shelf with the other bullets and not use them. They are probably collector worthy. I do load 90 and 100gr for the .380 and they work ok.