Collet Neck Sizing Dies have left the bench.

50 BMG, Collet, and steel reloading dies plus the Factory Crimp Dies. Also, discussions concerning the Deluxe, Pacesetter, and RGB die sets.

Re: Collet Neck Sizing Dies have left the bench.

Postby Jeff H » 31 Dec 2019 16

That's weird - the crack. I wonder if that is causing the collet to close too soon, meaning that the raised (it appears to be) edge of the crack is increasing the diameter of the cone at that point. That could make it grab too soon (vertically, as the collet/brass are raise with the ram) - like before the stroke hits peak.

Now, the following is untested blather:
I've only used these on an original Turret press; I clean, lap in and lubricate the parts of the die, make sure the mandrel is smooth and clean, with a light, light coat of oil; vigorously brush the insides of the case necks and steel wool the outsides of the case necks.

I also only resize the necks as lightly as necessary to hold onto the cast bullet during normal handling. I've NOT used cased so-sized in a lever-action, but have extensively in bolt-actions, specifically "CRF" Mauser actions. I cannot push the bullets into the case with my thumb and they don't "stick" in the rifling if I un-chamber a loaded round when the rifling engraves the bullet very slightly. The bullets won't tun in the necks with my fingers.

I've never tested this, but I've wondered about the tiny bit of vertical play in the decapping rods. It would seem likely that the spent primer would offer enough resistance to push the decapping rod up against the bottom of the threaded caps. If the decapping rod is too low, or the bottom of the brass (inside) is too high, that would impart a lot of force against that cap. Maybe the primers are just that hard to push out and the repeated stress blows out the cap or strips the threads?

So, if the decapping rod is pushed up against the bottom of the threaded cap by the resistance offered by the seated spent primer, and as the neck gets squeezed against the mandrel, does the neck slide against the madrel in the final few thousandths of an inch of upward travel? Or, does the mandrel drop back down after the primer is pushed all the way out, allowing it some vertical travel again so it can move up with the case/collet in the final little bit of upward travel?

Lastly, I would never assume you could hold a candle to me and my uncanny intermittent stupidity, but if it were on MY bench, I'd look to see if I'd mixed up madrels or collets or even had the right die. Just yesterday, I caught an unflared case mouth while loading 357 Mags. Since I use a turret press, this is a snap! Just rotate the turret to the flaring die, flare the case and you're all set, right? Wrong! You have to remember to rotate the turret BACK to the seating die. Yeah, I tried to seat a bullet with the flaring die - again. Give me another 50 years of hand-loading and I'll figure it all out. :oops:
Jeff H
Supporter
Supporter
 
Posts: 66
Joined: 30 Jun 2013
Has thanked: 26 times
Been thanked: 44 times
My Press Choice: Turret
Location: NW Ohio

Re: Collet Neck Sizing Dies have left the bench.

Postby Ranch Dog » 31 Dec 2019 18

Thanks for the reply. I've wondered about the mandrels/punches myself. I am used to checking the diameter of the mandrels as I have one under sized mandrel and three oversized mandrels (.001" increments) for each die. I keep them in individual trays for each die.
Michael
Image
User avatar
Ranch Dog
Site Admin
Site Admin
 
Posts: 5601
Joined: 22 Jun 2013
Has thanked: 1247 times
Been thanked: 2561 times
My Press Choice: Progressive
Location: Cuero, TX

Re: Collet Neck Sizing Dies have left the bench.

Postby JohnnyEnfield » 01 Jan 2020 22

My 308 collet die started doing that pushed/crushed shoulder thing all of a sudden. It was because the tapered part was sticking inside the cone hole and the cases would just get smooshed. I tried several things and ended up smoothing everything with emery cloth and then polish a few different times. Then putting anti seize compound in there. I have not had the issue since the last smoothing and adding the anti seize. I did not have a visible crack in mine. Disappointing because I really liked the dies.
Reduce, reuse, recycle, means- resize, reload, recycle.
User avatar
JohnnyEnfield
Supporter
Supporter
 
Posts: 148
Joined: 08 Dec 2017
Has thanked: 158 times
Been thanked: 47 times
My Press Choice: Single Stage
Location: Northeast USA

Previous

Return to Rifle

Who is online

Users browsing this forum: No registered users and 2 guests

  • Advertisement
cron