Six Pack Pro question- for those that are currently using one
-
- Supporter
- Posts: 78
- Joined: 19 Feb 2020 01:47
- My Press Choice: Progressive
- Location: McMillan, MI
- Has thanked: 19 times
- Been thanked: 10 times
Re: Six Pack Pro question- for those that are currently using one
Fyodor, I shoot a lot of different ARs, and don't feel comfortable with flush primers, due to the floating firing pin. Sometimes, not often, you can just let the gun go into battery, eject the round, and see a small spot where the firing pin hit the primer.
- GasGuzzler
- Moderator & Supporter
- Posts: 2045
- Joined: 26 Jan 2016 22:39
- My Press Choice: Turret
- Location: Cooke County, TX
- Has thanked: 330 times
- Been thanked: 501 times
Re: Six Pack Pro question- for those that are currently using one
Same here. And I never trim pistol brass either.Fyodor wrote: ↑18 Jan 2024 03:24 May I ask why you are not satisfied with flush primers?
While sorting my fresh loads into boxes, I check each and every primer with my finger to be at least flush. But they are considered good when flush, too. Just not protruding. I never had any problems with rounds not going off. Most of my guns are revolvers and lever rifles, but I also have two 1911s. The cowboy guns have drastically reduced main springs. All go off on the first strike, with the primer flush or seated deeply.
Is there anything I didn't see? Why is just flush not considered sufficient?
__________________________________________________________________________________________
I've always been crazy but it's kept me from goin' insane.
I've always been crazy but it's kept me from goin' insane.
-
- Posts: 60
- Joined: 18 Nov 2023 15:11
- My Press Choice: Progressive
- Location: SW New Mexico
- Has thanked: 24 times
- Been thanked: 4 times
Re: Six Pack Pro question- for those that are currently using one
I have had "slamFires" in my AR's when I first started loading them, I was buying all Federal primers then. A friend advised to switch to a "harder" primer, and gave me some CCI's, at the next CMP match I had no surprises!
- Fyodor
- Founding Member & Supporter
- Posts: 1514
- Joined: 04 Jan 2014 05:45
- My Press Choice: Progressive
- Location: Gernsbach, Germany
- Has thanked: 794 times
- Been thanked: 504 times
Re: Six Pack Pro question- for those that are currently using one
@BrianT:
I don't think a few thousands would make much of a difference.
I don't think a few thousands would make much of a difference.
"I disapprove of what you say, but I will defend to the death your right to say it"
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
- Evelyn Beatrice Hall, often misattributed to Voltaire
I think I'm thinking, therefore I may possibly be.
-
- Supporter
- Posts: 1003
- Joined: 09 Nov 2015 06:35
- My Press Choice: Single Stage
- Location: Washington State
- Has thanked: 38 times
- Been thanked: 274 times
Re: Six Pack Pro question- for those that are currently using one
Fyodor wrote: ↑18 Jan 2024 03:24 May I ask why you are not satisfied with flush primers?
While sorting my fresh loads into boxes, I check each and every primer with my finger to be at least flush. But they are considered good when flush, too. Just not protruding. I never had any problems with rounds not going off. Most of my guns are revolvers and lever rifles, but I also have two 1911s. The cowboy guns have drastically reduced main springs. All go off on the first strike, with the primer flush or seated deeply.
Is there anything I didn't see? Why is just flush not considered sufficient?
I do exactly as you do, run my fingers across the tops to make sure none are protruding. You can't really "feel" a 2 thousandth seating depth but I'll bet if you measure them as you seat your primers you'll find most all of them will be 2 or more thousandth deep. Perceived safety perhaps, but I've also read that primer seating depth should be from 2 thou all the way up to 8. A lot of information and opinions on that amount though. That pertains mostly to rifle reloading that I've read about. It can be a "hot" topic debate for sure. But that's just my preference and like you I've not had any misfires due to a flush primer If in fact I had primers that were "flush" seated because I don't check them all for sure. The 45acp rounds I did find that were just flush (0.00) probably would have fired just fine but the "perceived safety" with an auto loader reared it's ugly head for me.